File /code/strss7/include/sys/cdi.h

#ifndef _SYS_CDI_H
#define _SYS_CDI_H

#ident "@(#) cdi.h 1.15 3/28/99"



/*
 * Primitives for Local Management Services
 */
#define CD_INFO_REQ     	0x00	/* Information request */
#define CD_INFO_ACK     	0x01	/* Information acknowledgement */
#define CD_ATTACH_REQ   	0x02	/* Attach a PPA */
#define CD_DETACH_REQ   	0x03	/* Detach a PPA */
#define CD_ENABLE_REQ   	0x04	/* Prepare a device */
#define CD_DISABLE_REQ  	0x05	/* Disable a device */
#define CD_OK_ACK       	0x06	/* Success acknowledgement */
#define CD_ERROR_ACK    	0x07	/* Error acknowledgement */
#define CD_ENABLE_CON   	0x08	/* Enable confirmation */
#define CD_DISABLE_CON  	0x09	/* Disable confirmation */
#define CD_ERROR_IND    	0x0a	/* Error indication */

/*
 * Primitives used for Data Transfer
 */
#define CD_ALLOW_INPUT_REQ      0x0b	/* Allow input */
#define CD_READ_REQ     	0x0c	/* Wait-for-input request */
#define CD_UNITDATA_REQ 	0x0d	/* Data send request */
#define CD_WRITE_READ_REQ       0x0e	/* Write/read request */
#define CD_UNITDATA_ACK 	0x0f	/* Data send acknowledgement */
#define CD_UNITDATA_IND 	0x10	/* Data receive indication */
#define CD_HALT_INPUT_REQ       0x11	/* Halt input */
#define CD_ABORT_OUTPUT_REQ     0x12	/* Abort output */
#define CD_MUX_NAME_REQ		0x13	/* get mux name (Gcom) */
#define	CD_BAD_FRAME_IND	0x14	/* frame w/error (Gcom extension) */
#define	CD_MODEM_SIG_REQ	0x15	/* Assert modem signals (Gcom) */
#define	CD_MODEM_SIG_IND	0x16	/* Report modem signal state (Gcom) */
#define CD_MODEM_SIG_POLL	0x17	/* requests a CD_MODEM_SIG_IND (Gcom) */

/*
 * CDI device states
 */
#define CD_UNATTACHED   	0x00	/* No PPA attached */
#define CD_UNUSABLE     	0x01	/* PPA cannot be used */
#define CD_DISABLED     	0x02	/* PPA attached */
#define CD_ENABLE_PENDING       0x03	/* Waiting ack of enable req */
#define CD_ENABLED      	0x04	/* Awaiting use */
#define CD_READ_ACTIVE  	0x05	/* Input section enabled; */
					/* disabled after data arrives */
#define CD_INPUT_ALLOWED        0x06	/* Input section permanently enabled */
#define CD_DISABLE_PENDING      0x07	/* Waiting ack of disable req */
#define CD_OUTPUT_ACTIVE        0x08	/* Output section active only */
#define	CD_XRAY			0x09	/* Xray-ing another ppa */

/*
 * CD_ERROR_ACK and CD_ERROR_IND error return values
 */
#define CD_BADADDRESS   0x01	/* Address was invalid */
#define CD_BADADDRTYPE  0x02	/* Invalid address type */
#define CD_BADDIAL      0x03	/* Dial information was invalid */
#define CD_BADDIALTYPE  0x04	/* Invalid dial information type */
#define CD_BADDISPOSAL  0x05	/* Invalid disposal parameter */
#define CD_BADFRAME     0x06	/* Defective SDU received */
#define CD_BADPPA       0x07	/* Invalid PPA identifier */
#define CD_BADPRIM      0x08	/* Unrecognized primitive */
#define CD_DISC 	0x09	/* Disconnected */
#define CD_EVENT        0x0a	/* Protocol-specific event occurred */
#define CD_FATALERR     0x0b	/* Device has become unusable */
#define CD_INITFAILED   0x0c	/* Line initialization failed */
#define CD_NOTSUPP      0x0d	/* Primitive not supported by this device */
#define CD_OUTSTATE     0x0e	/* Primitive was issued from an invalid state */
#define CD_PROTOSHORT   0x0f	/* M_PROTO block too short */
#define CD_READTIMEOUT  0x10	/* Read request timed out before data arrived */
#define CD_SYSERR       0x11	/* UNIX system error */
#define CD_WRITEFAIL    0x12	/* Unitdata request failed */

/*
 * Error explanations
 */
#define CD_CRCERR       	0x01	/* CRC or FCS error */
#define CD_DLE_EOT      	0x02	/* DLE EOT detected */
#define CD_FORMAT       	0x03	/* Format error detected */
#define CD_HDLC_ABORT   	0x04	/* Aborted frame detected */
#define CD_OVERRUN      	0x05	/* Input overrun */
#define CD_TOOSHORT     	0x06	/* Frame too short */
#define CD_INCOMPLETE   	0x07	/* Partial frame received */
#define CD_BUSY 		0x08	/* Telephone was busy */
#define CD_NOANSWER     	0x09	/* Connection went unanswered */
#define CD_CALLREJECT   	0x0a	/* Connection rejected */
#define CD_HDLC_IDLE    	0x0b	/* HDLC line went idle */
#define CD_HDLC_NOTIDLE 	0x0c	/* HDLC line no longer idle */
#define CD_QUIESCENT    	0x0d	/* Line being reassigned */
#define CD_RESUMED      	0x0e	/* Line has been reassigned */
#define CD_DSRTIMEOUT   	0x0f	/* Did not see DSR in time */
#define CD_LAN_COLLISIONS       0x10	/* LAN excessive collisions */
#define CD_LAN_REFUSED  	0x11	/* LAN message refused */
#define CD_LAN_NOSTATION        0x12	/* LAN no such station */
#define CD_LOSTCTS      	0x13	/* Lost Clear to Send signal */
#define CD_DEVERR       	0x100	/* Start of device-specific codes */

/*
 * CDI device classes
 */
#define CD_HDLC 	0x00	/* Bit-synchronous */
#define CD_BISYNC       0x01	/* Character-synchronous */
#define CD_LAN          0x02	/* ISO 8802-3,4,5 local-area network MAC */
#define	CD_NODEV	0x03	/* no device, ppa used for X-ray */

/*
 * CDI duplex types
 */
#define CD_FULLDUPLEX   0x00	/* Full duplex; allow input supported */
#define CD_HALFDUPLEX   0x01	/* Half duplex; read and write/read supported */

/*
 * CDI output styles
 */
#define CD_UNACKEDOUTPUT 0x00	/* No unitdata acknowledgements */
#define CD_ACKEDOUTPUT   0x01	/* Unitdata acknowledgements */
#define CD_PACEDOUTPUT   0x02	/* Unitdata acks as output timing hints */

/*
 * CDI optional features
 */
#define CD_CANREAD      0x01	/* Read request supported on full duplex */
#define CD_CANDIAL      0x02	/* Dial information supported */
#define CD_AUTOALLOW    0x04	/* CD_INPUT_ALLOWED as soon as enabled */
#define CD_KEEPALIVE	0x08	/* Gcom: Don't send off at CD_DISABLE_REQ */

/*
 * CDI provider style.
 * The CDI provider style which determines whether a provider
 * requires a CD_ATTACH_REQ to inform the provider which PPA
 * user messages should be sent/received on.
 */
#define CD_STYLE1       0x00	/* PPA is implicitly bound by open(2) */
#define CD_STYLE2       0x01	/* PPA must be explicitly bound via CD_ATTACH_REQ */
#define	CD_STYLE_1	CD_STYLE1	/* Gcom -- to match document */
#define	CD_STYLE_2	CD_STYLE2	/* Gcom -- to match document */

/*
 * Symbolic value for "no dialing information"
 */
#define CD_NODIAL       0x00

/*
 * Actions to take with undelivered data in a CD_DISABLE_REQ or
CD_HALT_INPUT_REQ
 */
#define CD_FLUSH        0x00	/* Discard undelivered data */
#define CD_WAIT 	0x01	/* Attempt to deliver unsent data */
#define CD_DELIVER      0x02

/*
 * Address types
 */
#define CD_SPECIFIC     0x00	/* Specific address follows */
#define CD_BROADCAST    0x01	/* Broadcast; no address follows */
#define CD_IMPLICIT     0x02	/* No address or embedded address */

/*
 * Error types for CD_BAD_FRAME_IND
 */

#define	CD_FRMTOOLONG	0xFFFF	/* frame overflowed rcv bfr */
#define	CD_FRMNONOCTET	0xFFFE	/* frame not octet-aligned */
#define	CD_EMPTY_BFR	0xFFFD	/* empty rcv buffer (not used) */
#define	CD_BAD_CRC	0xFFFC	/* CRC error */
#define	CD_FRM_ABORTED	0xFFFB	/* frame aborted */
#define	CD_RCV_OVERRUN	0xFFFA	/* receive overrun */

/*
 * Modem signal bits for modem signal related requests and indications
 */
#define CD_DTR		0x01
#define CD_RTS		0x02
#define CD_DSR		0x04
#define CD_DCD		0x08
#define CD_CTS		0x10
#define CD_RI		0x20

/*
 * CDI interface primitive definitions.
 *
 * Each primitive is sent as a Stream message.  It is possible that
 * the messages may be viewed as a sequence of bytes that have the
 * following form without any padding. The structure definition
 * of the following messages may have to change depending on the
 * underlying hardware architecture and crossing of a hardware
 * boundary with a different hardware architecture.
 *
 * Each message has the name defined followed by the
 * Stream message type (M_PROTO, M_PCPROTO, M_DATA)
 */

typedef unsigned long cd_ulong;
typedef unsigned short cd_ushort;

/*
 *      LOCAL MANAGEMENT PRIMITIVES
 */

/*
 * CD_INFO_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
} cd_info_req_t;

/*
 * CD_INFO_ACK, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
	cd_ulong cd_max_sdu;
	cd_ulong cd_min_sdu;
	cd_ulong cd_class;
	cd_ulong cd_duplex;
	cd_ulong cd_output_style;
	cd_ulong cd_features;
	cd_ulong cd_addr_length;
	cd_ulong cd_ppa_style;
} cd_info_ack_t;

/*
 * CD_ATTACH_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_ppa;
} cd_attach_req_t;

/*
 * CD_DETACH_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
} cd_detach_req_t;

/*
 * CD_ENABLE_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_dial_type;
	cd_ulong cd_dial_length;
	cd_ulong cd_dial_offset;
} cd_enable_req_t;

/*
 * CD_DISABLE_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_disposal;
} cd_disable_req_t;

/*
 * CD_OK_ACK, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
	cd_ulong cd_correct_primitive;
} cd_ok_ack_t;

/*
 * CD_ERROR_ACK, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
	cd_ulong cd_error_primitive;
	cd_ulong cd_errno;
	cd_ulong cd_explanation;
} cd_error_ack_t;

/*
 * CD_ENABLE_CON, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
} cd_enable_con_t;

/*
 * CD_DISABLE_CON, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
} cd_disable_con_t;

/*
 * CD_ERROR_IND, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
	cd_ulong cd_errno;
	cd_ulong cd_explanation;
} cd_error_ind_t;

/*
 *      DATA TRANSFER PRIMITIVES
 */

/*
 * CD_ALLOW_INPUT_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
} cd_allow_input_req_t;

/*
 * CD_READ_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_msec;
} cd_read_req_t;

/*
 * CD_UNITDATA_REQ, optional M_PROTO type, with M_DATA block(s)
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ushort cd_addr_type;
	cd_ushort cd_priority;
	cd_ulong cd_dest_addr_length;
	cd_ulong cd_dest_addr_offset;
} cd_unitdata_req_t;

/*
 * CD_WRITE_READ_REQ, M_PROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_unitdata_req_t cd_unitdata_req;
	cd_read_req_t cd_read_req;
} cd_write_read_req_t;

/*
 * CD_UNITDATA_ACK, M_PROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
} cd_unitdata_ack_t;

/*
 * CD_UNITDATA_IND, optional M_PROTO type, with M_DATA block(s)
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
	cd_ulong cd_src_addr_length;
	cd_ulong cd_src_addr_offset;
	cd_ushort cd_addr_type;
	cd_ushort cd_priority;
	cd_ulong cd_dest_addr_length;
	cd_ulong cd_dest_addr_offset;
} cd_unitdata_ind_t;

/*
 * CD_BAD_FRAME_IND, M_PROTO type, with M_DATA block(s)
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_state;
	cd_ulong cd_error;		/* what is wrong with the frame */

} cd_bad_frame_ind_t;

/*
 * CD_MODEM_SIG_REQ, M_PROTO type
 *
 * Assert the modem signals with '1' bits in the cd_sigs mask and
 * drop those signals with '0' bits.  Sensed modem signals such
 * as DCD or CTS are ignored.
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_sigs;

} cd_modem_sig_req_t;

/*
 * CD_MODEM_SIG_IND, M_PROTO type
 *
 * The cd_sigs field reports the current state of the modem signals.
 * This message is sent when modem signals change at the hardware
 * interface.  Only changes in signals selected by the cd_modem_sig_enb_req_t
 * cd_sigs mask will be evaluated for purposes of change detection.
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_sigs;

} cd_modem_sig_ind_t;

typedef struct {
	cd_ulong cd_primitive;

} cd_modem_sig_poll_t;

/*
 * CD_HALT_INPUT_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
	cd_ulong cd_disposal;
} cd_halt_input_req_t;

/*
 * CD_ABORT_OUTPUT_REQ, M_PROTO or M_PCPROTO type
 */
typedef struct {
	cd_ulong cd_primitive;
} cd_abort_output_req_t;

union CD_primitives {
	cd_ulong cd_primitive;
	cd_info_req_t info_req;
	cd_info_ack_t info_ack;
	cd_attach_req_t attach_req;
	cd_detach_req_t detach_req;
	cd_enable_req_t enable_req;
	cd_disable_req_t disable_req;
	cd_ok_ack_t ok_ack;
	cd_error_ack_t error_ack;
	cd_enable_con_t enable_con;
	cd_disable_con_t disable_con;
	cd_error_ind_t error_ind;
	cd_allow_input_req_t allow_input_req;
	cd_read_req_t read_req;
	cd_unitdata_req_t unitdata_req;
	cd_write_read_req_t write_read_req;
	cd_unitdata_ack_t unitdata_ack;
	cd_unitdata_ind_t unitdata_ind;
	cd_halt_input_req_t halt_input_req;
};

#define CD_INFO_REQ_SIZE                sizeof(cd_info_req_t)
#define CD_INFO_ACK_SIZE                sizeof(cd_info_ack_t)
#define CD_ATTACH_REQ_SIZE              sizeof(cd_attach_req_t)
#define CD_DETACH_REQ_SIZE              sizeof(cd_detach_req_t)
#define CD_ENABLE_REQ_SIZE              sizeof(cd_enable_req_t)
#define CD_DISABLE_REQ_SIZE             sizeof(cd_disable_req_t)
#define CD_OK_ACK_SIZE          	sizeof(cd_ok_ack_t)
#define CD_ERROR_ACK_SIZE               sizeof(cd_error_ack_t)
#define CD_ALLOW_INPUT_REQ_SIZE 	sizeof(cd_allow_input_req_t)
#define CD_READ_REQ_SIZE                sizeof(cd_read_req_t)
#define CD_UNITDATA_REQ_SIZE            sizeof(cd_unitdata_req_t)
#define CD_WRITE_READ_REQ_SIZE  	sizeof(cd_write_read_req_t)
#define CD_UNITDATA_ACK_SIZE            sizeof(cd_unitdata_ack_t)
#define CD_UNITDATA_IND_SIZE            sizeof(cd_unitdata_ind_t)
#define CD_HALT_INPUT_REQ_SIZE          sizeof(cd_halt_input_req_t)
#define CD_ABORT_OUTPUT_REQ_SIZE        sizeof(cd_abort_output_req_t)
#define CD_ERROR_IND_SIZE               sizeof(cd_error_ind_t)
#define CD_ENABLE_CON_SIZE              sizeof(cd_enable_con_t)
#define CD_DISABLE_CON_SIZE             sizeof(cd_disable_con_t)
#define CD_BAD_FRAME_IND_SIZE		sizeof(cd_bad_frame_ind_t)
#define CD_MODEM_SIG_REQ_SIZE		sizeof(cd_modem_sig_req_t)
#define CD_MODEM_SIG_IND_SIZE		sizeof(cd_modem_sig_ind_t)
#define CD_MODEM_SIG_POLL_SIZE		sizeof(cd_modem_sig_poll_t)

#endif				/* _SYS_CDI_H */